Trade.Information

Details of Alternative Fuel Vehicle

Alternative Fuel Vehicle refers to a vehicle that runs on a fuel other than traditional gasoline or diesel; any method of powering an engine that does not involve solely petroleum (e.g. electric car, gasoline-electric hybrid, solar powered). Due to a combination of heavy taxes on fuel, particularly in Europe, tightening environmental laws, particularly in California, and the possibility of further restrictions on greenhouse gas emissions, work on alternative power systems for vehicles has become a high priority for governments and vehicle manufacturers around the world.

Current research and development is largely centered on "hybrid" vehicles that use both electric power and internal combustion. The first hybrid vehicle available for sale in the United States was the Honda Insight, achieving around 70 miles per gallon (25.5km per liter).

Other research and development efforts in alternative forms of power focus on developing fuel cells, alternative forms of combustion such as GDI and HCCI, and even the stored energy of compressed air.

Greasestock is an event held yearly in Yorktown Heights, New York which is one of the largest showcases of alternative fuel vehicles in the United States.
Single fuel source

Air car
The air engine is an emission-free piston engine that uses compressed air as a source of energy. The first compressed air car was invented by a French engineer named Guy Nègre, 58.

The expansion of compressed air may be used to drive the pistons in a modified piston engine. Efficiency of operation is gained through the use of environmental heat at normal temperature to warm the otherwise cold expanded air from the storage tank. This non-adiabatic expansion has the potential to greatly increase the efficiency of the machine. The only exhaust is cold air (−15 °C), which could also be used to air condition the car. The source for air is a pressurized carbon-fiber tank holding air at 3,000 lbf/in² (20 MPa). Air is delivered to the engine via a rather conventional injection system. Unique crank design within the engine increases the time during which the air charge is warmed from ambient sources and a two stage process allows improved heat transfer rates.

This engine was used to power an urban car with room for five passengers and a projected range of about 100 to 200 miles (160 to 320 km), depending on traffic conditions. The main advantages are: no roadside emissions, low cost technology, engine uses food oil for lubrication (just about 1 liter, changes only every 30,000 miles (50,000 km) and integrated air conditioning. Range could be quickly tripled, since there are already carbon fiber tanks which have passed safety standards holding gas at 10,000 lbf/in² (70 MPa).

The tanks may be refilled in about three minutes at a service station, or in a few hours at home plugging the car into the electric grid via an on-board compressor. The cost of refilling is projected to be about US$3.

Battery-electric
Battery Electric Vehicles (BEVs) are electric vehicles whose main energy storage is in the chemical energy of batteries. BEVs are the most common form of what is defined by the California Air Resources Board (CARB) as zero emission (ZEV) passenger automobiles, because they produce no emissions while being driven. The electrical energy carried onboard a BEV to power the motors is obtained from a variety of battery chemistries arranged into battery packs. For additional range genset trailers or pusher trailers are sometimes used, forming a type of hybrid vehicle. Batteries used in electric vehicles include "flooded" lead-acid, absorbed glass mat, NiCd, nickel metal hydride, Li-ion, Li-poly and zinc-air batteries.

Attempts at building viable, modern battery-powered electric vehicle began in the 1950s with the introduction of the first modern (transistor controlled) electric car - the Henney Kilowatt. Despite the poor sales of the early battery-powered vehicles, development of various battery-powered vehicles continued through the 1960(notably General Motors with the EV1), but cost, speed and inadequate driving range continued to make them impractical. Battery powered cars have primarily used lead-acid batteries and NiMH batteries. Lead-acid batteries' recharge capacity is considerably reduced if they're discharged beyond 75% on a regular basis, making them a less-than-ideal solution. NiMH batteries are a better choice, but are considerably more expensive than lead-acid. Lithium-ion battery powered vehicles such as the Venturi Fetish have recently demonstrated excellent performance and range, but they remain very expensive.

Biofuels
Bioalcohol / Ethanol
The use of alcohol as a fuel for internal combustion engines, either alone or in combination with other fuels, has been given much attention mostly because of its possible environmental and long-term economical advantages over fossil fuel.

Both ethanol and methanol have been considered for this purpose. While both can be obtained from petroleum or natural gas, ethanol may be the most interesting because many believe it to be a renewable resource, easily obtained from sugar or starch in crops and other agricultural produce such as grain, sugarcane or even lactose. Since ethanol occurs in nature whenever yeast happens to find a sugar solution such as overripe fruit, most organisms have evolved some tolerance to ethanol, whereas methanol is toxic. Other experiments involve butanol, which can also be produced by fermentation of plants.

When alcohol fuel is mixed into gasoline, the result is known as gasohol and labelled with an 'E' followed by the percentage of Ethanol. E10 is commonly found throughout the southern United States, E20 will be mandated by the U.S. state of Minnesota by 2013. and E85 (containing 85% ethanol and just 15% of gasoline) is slowly becoming available. E100 is straight ethanol, which is most widely used in Brazil and Argentina.

Use of pure ethanol and ethanol/gasoline mixtures is not without problems however. Ethanol has the unfortunate property of slowly decomposing certain rubber compounds such as are found in the fuel lines and seals in vehicles produced before the mid 1980s. There are claims that even E10 can have a significantly deleterious effect on older vehicles and after prolonged use may cause dangerous fuel leaks in affected cars. Because gasoline is more volatile than Ethanol, it can be harder to start some engines using higher Ethanol percentages than they were designed to use - especially when the engine is cold - and even modern vehicles may be unable to run more than 20% ethanol for this reason. Because of the difficulty of starting engines using ethanol, it is common practice in E100 countries such as Brazil to have a small gasoline reservoir in addition to the normal fuel tank with a switch to allow the driver to switch over to gasoline when the car has difficulties starting on ethanol alone. Ethanol is also electrically conductive (gasoline is an effective insulator) which can cause problems with some early electric fuel pump designs and fuel tank sensors. Corrosion of magnesium and aluminium parts is also a concern at higher ethanol percentages. Ethanol has less energy per volume than gasoline so miles-per-gallon ratings with ethanol mixtures are significantly worse than with pure gasoline - although ethanol has a higher octane rating which is beneficial to high compression ratio engines.

Many cars that currently use gasoline can run on ethanol, a fuel made from plant sugars. Most cars that are designed to run on gasoline are capable of running with up to 15% ethanol mixed into gasoline. With a small amount of redesign, gasoline-powered vehicles can run on ethanol concentrations as high as 85%. Most gasoline fuelled vehicles can be modified to run on LPG but there has been some concern that the ethanol-gasoline mixtures prematurely wear down seals and gaskets. Theoretically, the lower energy content of alcohol should lead to considerably reduced efficiency and range when compared with gasoline. However, EPA testing has actually shown only a 20-30% reduction in range. Therefore, if the vehicle is capable of doing 750 kilometers on a 50 liter tank (15 kilometers per liter), its range would be reduced to approximately 600 kilometers (12 kilometers per liter). Measures are available to increase this efficiency, such as different camshaft configurations, altering the timing/spark output of the ignition, increasing compression, or simply using a larger fuel tank.

In the United States, alcohol fuel was produced in corn-alcohol stills until Prohibition criminalized the production of alcohol in 1919. Interest in alcohol as an automotive fuel lapsed until the oil price shocks of the 1970s. Reacting to the high price of oil and its growing dependence on imports, in 1975 Brazil launched a huge government-subsidized effort to manufacture ethanol fuel (from its sugar cane crop) and ethanol-powered automobiles. These ethanol-only vehicles were very popular in the 1980s, but became economically impractical when oil prices fell - and sugar prices rose - late in that decade. In recent years Brazil has encouraged the development of flex-fuel automobiles, where the owner can use any mixture of ethanol and gasoline based on their individual cost and performance goals. In 2005, 70% of the cars sold in Brazil were flex-fuel.

Biodiesel
The main benefit of Diesel combustion engines is that they have a 50% fuel burn efficiency; compared with just 23% in the best gasoline engines. This makes Diesel engines capable of achieving much better fuel efficiency than gasoline vehicles.
Biodiesel is commercially available in most oilseed-producing states in the United States. As of 2005, it is somewhat more expensive than fossil diesel, though it is still commonly produced in relatively small quantities (in comparison to petroleum products and ethanol). Many farmers who raise oilseeds use a biodiesel blend in tractors and equipment as a matter of policy, to foster production of biodiesel and raise public awareness. It is sometimes easier to find biodiesel in rural areas than in cities.

Some Diesel-powered cars can run with little or no modification on 100% pure biodiesel, a fuel that can be made from vegetable oils. Vegetable oils tend to solidify in cold weather conditions so vehicle modifications may be required in order to heat the fuel prior to use under those circumstances. Modern low emission diesels (most often Euro -3 and -4 compliant), typical of the current production in the European industry, require extensive modification of injector system, pumps and seals etc. due to the higher operating pressures. The result is sensitive lubrication & sealing systems that bio diesel fuels do not protect and may even attack. This reduces the market for bio diesels as increasing numbers of new vehicles are not able to use it.

Biogas
Compressed Biogas may be used for Internal Combustion Engines after purification of the raw gas. The removal of H2O, H2S and particles can be seen as standard producing a gas which has the same quality as Compressed Natural Gas. The use of biogas is particularly interesting for climates where the waste heat of a biogas powered power plant cannot be used during the summer.

CNG Compressed Natural Gas
High pressure compressed natural gas, mainly composed of methane, that is used to fuel normal combustion engines instead of gasoline. Combustion of methane produces the least amount of CO2 of all fossil fuels. Gasoline cars can be retrofitted to CNG and become bifuel NGV Natural gas vehicles as the gasoline tank stays. You can switch between CNG and gasoline during operation. Estimated over 5 million CNG vehicles running worldwide.

Hydrogen
A hydrogen car is an automobile which uses hydrogen as its primary source of power for locomotion. These cars generally use the hydrogen in one of two methods: combustion or fuel-cell conversion. In combustion, the hydrogen is "burned" in engines in fundamentally the same method as traditional gasoline cars. In fuel-cell conversion, the hydrogen is turned into electricity through fuel cells which then powers electric motors. With either method, the only byproduct from the spent hydrogen is water.

A small number of prototype hydrogen cars currently exist, and a significant amount of research is underway to make the technology more viable. The common internal combustion engine, usually fueled with gasoline (petrol) or diesel liquids, can be converted to run on gaseous hydrogen. However, the most efficient use of hydrogen involves the use of fuel cells and electric motors instead of a traditional engine. Hydrogen reacts with oxygen inside the fuel cells, which produces electricity to power the motors. One primary area of research is hydrogen storage, to try to increase the range of hydrogen vehicles while reducing the weight, energy consumption, and complexity of the storage systems. Two primary methods of storage are metal hydrides and compression. Some believe that hydrogen cars will never be economically viable and that the emphasis on this technology is a diversion from the development and popularization of more efficient hybrid cars and other alternative technologies.

High speed cars, buses, motorcycles, bicycles, submarines, and space rockets already run on hydrogen, in various forms. There is even a working toy model car that runs on solar power, using a reversible fuel cell to store energy in the form of hydrogen and oxygen gas. It can then convert the fuel back into water to release the solar energy.

BMW's Clean Energy internal combustion hydrogen car has more power and is faster than hydrogen fuel cell electric cars. A limited series production of the 7 Series Saloon was announced as commencing at the end of 2006. A BMW hydrogen prototype (H2R) using the driveline of this model broke the speed record for hydrogen cars at 300 km/h (186 mi/h), making automotive history. Mazda has developed Wankel engines to burn hydrogen. The Wankel uses a rotary principle of operation, so the hydrogen burns in a different part of the engine from the intake. This reduces pre-detonation, a problem with hydrogen fueled piston engines.
The other major car companies like Daimler, Chrysler, Honda, Toyota, Ford and General Motors, are investing in hydrogen fuel cells instead. VW, Nissan, and Hyundai/Kai also have fuel cell vehicle protoypes on the road. In addition, transit agencies across the globe are running prototype fuel cell buses. Fuel cell vehicles, such as the new Honda Clarity, can get up to 70 miles on a kilogram of hydrogen (roughly equivilent to a gallon of gasoline.)

Liquid Nitrogen car
Liquid nitrogen (LN2) is a method of storing energy. Energy is used to liquify air, and then LN2 is produced by evaporation, and distributed. LN2 is exposed to ambient heat in the car and the resulting nitrogen gas can be used to power a piston or turbine engine. The maximum amount of energy that can be extracted from 1 kg of LN2 is 213 W-hr or 173 W-hr per liter, in which a maximum of 70 W-hr can be utilized with an isothermal expansion process. Such a vehicle can achieve ranges similar to that of gasoline with a 350 liter (90 gallon) tank. Theoretical future engines, using cascading topping cycles, can improve this to around 110 W-hr/kg with a quasi-isothermal expansion process. The advantages are zero harmful emissions and superior energy densities than compressed air, and a car powered by LN2 can be refilled in a matter of minutes.

LPG or Autogas
LPG or liquified petroleum gas is a low pressure liquified gas mixture composed mainly of propane and butane which burns in conventional gasoline combustion engines with less CO2 than gasoline. Gasoline cars can be retrofitted to LPG aka Autogas and become bifuel vehicles as the gasoline tank stays. You can switch between LPG and gasoline during operation. Estimated 10 million vehicles running worldwide.

Propane
A vehicle powered by propane.

Solar
A solar car is an electric vehicle powered by solar energy obtained from solar panels on the car. Solar cars are not a practical form of transportation; insufficient power falls on the roof of a practically sized and shaped vehicle to provide adequate performance. They are raced in competitions such as the World Solar Challenge and the North American Solar Challenge. These events are often sponsored by Government agencies such as the United States Department of Energy keen to promote the development of alternative energy technology such as solar cells and electric vehicles. Such challenges are often entered by universities to develop their students engineering and technological skills as well as motor vehicle manufacturers such as GM and Honda.

The North American Solar Challenge is a solar car race across North America. Originally called Sunrayce, organized and sponsored by General Motors in 1990, it was renamed American Solar Challenge in 2001, sponsored by the United States Department of Energy and the National Renewable Energy Laboratory. Teams from universities in the United States and Canada compete in a long distance test of endurance as well as efficiency, driving thousands of miles on regular highways.
Nuna is the name of a series of manned solar powered vehicles that won the World solar challenge in Australia three times in a row, in 2001 (Nuna 1 or just Nuna), 2003 (Nuna 2) and 2005 (Nuna 3). The Nunas are built by students of the Delft University of Technology.

The World solar challenge is a solar powered car race over 3021 km through central Australia from Darwin to Adelaide. The race attracts teams from around the world, most of which are fielded by universities or corporations although some are fielded by high schools.

Steam
A steam car is a car that has a steam engine. Wood, coal, ethanol, or others can be used as fuel. The fuel is burned in a boiler and the heat converts water into steam. When the water turns to steam, it expands. The expansion creates pressure. The pressure pushes the pistons back and forth. This turns the driveshaft to spin the wheels forward. It works like a coal-fueled steam train, or steam boat. The steam car was the next logical step in independent transport.
Steam cars take a long time to start, but some can reach speeds over 100 mph (161 km/h) eventually.

A steam engine uses external combustion, as opposed to internal combustion. Gasoline-powered cars are more efficient at about 25-28% efficiency. In theory, a combined cycle steam engine in which the burning material is first used to drive a gas turbine can produce 50% to 60% efficiency. However, practical examples of steam engined cars work at only around 5-8% efficiency.

The best known and best selling steam-powered car was the Stanley Steamer. It used a compact fire-tube boiler under the hood to power a simple two-piston engine which was connected directly to the rear axle. Before Henry Ford introduced monthly payment financing with great success, cars were typically purchased outright. This is why the Stanley was kept simple; to keep the purchase price affordable.

Steam produced in refrigeration also can be use by a turbine in other vehicle types to produce electricity, that can be employed in electric motors or stored in a battery.

Steam power can be combined with a standard oil-based engine to create a hybrid. Water is injected into the cylinder after the fuel is burned, when the piston is still superheated, often at temperatures of 1500 degrees or more. The water will instantly be vaporized into steam, taking advantage of the heat that would otherwise be wasted.

Wood gas
Wood gas can be used to power cars with ordinary internal combustion engines if a wood gasifier is attached. This was quite popular during World War II in several European and Asian countries because the war prevented easy and cost-effective access to oil.

Multiple fuel source
Flexible fuel
A flexible-fuel vehicle or dual-fuel vehicle is an automobile or truck (lorry) that can typically alternate between two sources of fuel. A common example is a vehicle that can accept gasoline mixed with varying levels of ethanol (gasohol). Some cars carry a natural gas tank and one can switch from gasoline to gas.
North American vehicles from approximately 1980 onward can run on 10% ethanol/90% gasoline (e.g., E10) with no modifications. Prior to 1980, many cars imported into the United States contained rubber, aluminium, and other materials that were generally non-compatible with any ethanol in their fuel delivery systems, and these cars experienced problems when E10 was first introduced. American made cars from the late 1970s onward can run on E10 with no modifications. E10 fuel is widely available. Going beyond 10% ethanol generally requires special engineering.

In the United States, many flexible-fuel vehicles can accept up to 85% ethanol (E85). The fuel mixture is automatically detected by one or more sensors, and once detected, the ECU tunes the timing of spark plugs and fuel injectors so that the fuel will burn cleanly in the vehicle's internal combustion engine. Originally, sensors in both the fuel-line and in the exhaust system were used for flexible fuel vehicles. In recent years, manufacturers have instead opted to use only sensors in the exhaust manifold, before the catalytic converter, and to eliminate the fuel inline sensor. As E85 is more corrosive, special fuel lines are also required. Some manufacturers also required a different motor oil be used, but even this requirement is now dropped for all but one manufacturer.

Hybrid
A hybrid vehicle uses multiple propulsion systems to provide motive power. This most commonly refers to gasoline-electric hybrid vehicles, which use gasoline (petrol) and electric batteries for the energy used to power internal-combustion engines (ICEs) and electric motors. These powerplants are usually relatively small and would be considered "underpowered" by themselves, but they can provide a normal driving experience when used in combination during acceleration and other maneuvers that require greater power.

The Toyota Prius is one of the world's first commercially mass-produced and marketed hybrid automobiles. Manufactured by Toyota, the Prius first went on sale in Japan in 1997. The car was introduced to the worldwide market in 2000 and almost 160,000 units had been produced for sale in Japan, Europe, and North America as of the end of 2003. As of May 15th, 2008 Toyota had announced that it had reached a sales figure surpassing the mark of one million units. Toyota Press Release

The Honda Insight is a 2-seater hatchback hybrid automobile manufactured by Honda. It was the first mass-produced hybrid automobile sold in the United States, introduced in 1999, and produced until 2006. Honda now offers the Civic and Honda Accord as optional hybrids.

Pedal Assisted Electric Hybrid Vehicle
In very small vehicles, the power demand decreases, so human power can be employed to make a significant improvement in battery life. Two such commercially made vehicles are the Sinclair C5 and the TWIKE.
 

Type: Glossary & Dictionary